Wheels

Zipp's 303 Firecrest Tubeless wheels are designed for the real world—a world of imperfect conditions, varying road surfaces, and elements where the bottom line is simple: efficiency = speed. They're faster, lighter, and more capable over varied terrain—whether the surface is pavement in all its conditions or no pavement at all. Deeply rooted in Zipp's drive to conquer the Spring Classics, the new 303 Firecrest is remade with a purpose-made approach for the demands of modern road bikes. When it comes to going fast on a bicycle, efficiency means reduced wind resistance, rolling resistance, rider fatigue, and weight. The 303 Firecrest Tubeless Disc-brake was designed using real-world direct measurements (vs. primarily wind tunnel or computer simulation). The results were huge. Its rim is slightly more bulbous in design than its predecessor, with a 32mm outside width, a 25mm internal width, and a 40mm rim depth. The profile provides low drag and an improved transition between rim and tire, boosting aero efficiency on the road. The wide rim stance also features less tire deflection for reduced rolling resistance. The combination of the wider tire, increased tire volume, and lower tire pressure helps to reduce rider fatigue by smoothing out the ride over imperfect pavement and road conditions—the tire and wheel system absorbs the shaking, not the rider. The 303 Firecrest Tubeless wheels are for dedicated cyclists who aspire to the latest in technology. They're for those who compete in races, against peers, or simply to conquer personal limits. - New Zipp graphics and cosmetic identity that scream speed - Versatile endurance wheelset for the modern road bike with tubeless and hookless rim profile - Lighter weight than its predecessor, making it nimble and fast - Tubeless Made Easy, optimized tire bed sign allows for simple tool-free installation and removal with no need for an air compressor to seat the tire. - Ultra-wide 25mm rim profile creates a better tire interface to be fast on or off the road - 40mm rim depth makes a light and aero wheel in every situation - Ships with 12mm end caps - Center Lock rotor interface (lockring included)

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Trainer Caps allow thru-axle bikes to be used with most wind, magnetic or fluid cycling trainers. Cold weather and short days are never far from a Minnesotan's mind so Wolf Tooth engineers created Trainer Caps to reduce barriers to winter workouts. Non-drive side axle caps are joined by drive-side plugs that can be installed or removed without tools to make the prospect of hopping on the trainer a little more bearable. - Compatibility: Wolf Tooth Rear Axles (not compatible with rear axles from other manufacturers) - Plug has O-ring retention – no tool required

- Cold forged 304 stainless steel with rolled threads - Lightweight 2.0mm/1.7mm/2.0mm double-butted form - Nipples sold separately - 172g (32 spokes @ 262mm) - Bag of 50

- Cold forged 2.0mm 304 stainless steel with rolled threads - Nipples sold separately - 213g (32 spokes @ 262mm) - Bag of 50

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs - Type: Solid Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 174mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 174mm - 1 axle per bag

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

- Evo Tour 19 27.5" double wall rim—Black - Inner Rim Width: 19 mm - Rim Height: 20 mm - Pin joint construction - No Eyelets - Schrader valve - 36 holes - Stainless steel spokes—Silver - Freewheel

- EVO E-Tour 20 24" double wall rim - Silver - Inner Rim Width: 19.8 mm - Rim Height: 16.8 mm - Pin joint construction - No Eyelets - Schrader valve - 36 holes

- Rims: WTB ST i30 (Black), inner width: 30 mm - New TCS 2.0 Tubeless system - Solid Strip (included) protects and ensures a smooth surface between the tire and the rim - Easy On-Ramp profile allows for a smooth tire installation and stress- free inflation - Industrial Epoxy reinforced Pinned Joint provides repeatable tubeless consistency - Drilled for Presta valve - 32 holes - Rear hub (1): Formula DHT148 (Black), Laser etched logo, 12mm TA, O.L.D. 148mm BOOST - Rear hub (2): Formula DC2241 (Black), Laser etched logo, M9x141mm BOOST141 - HG Freehub compatible with 8-10, MTB 11-speed - 6-bolt disc mount - Sealed bearings (DC711 & DHT148) - TA Axles not incl. - Quick Release binder included (DC2241) - Tubeless Compatible (Tubeless Valve included) Assembled in North America by experienced wheel builders with Sapim 14G Stainless Steel spokes (Black) and 14mm Brass Polyax Nipples (Black)

Built for bashing, whether on a gravity shred sled or fully loaded bikepacking rig, WTB's KOM Tough rims are extruded from top-tier alloy to provide utmost durability at a reasonable weight. Their legendary I-Beam construction has evolved to further reinforce the rim with dual support beams that provide increased strength and stiffness for the world's most aggressive riders. KOM Tough rims are proven on the toughest tracks of the Enduro World Series, depended on for daily trail rides, and trusted while bikepacking in remote regions of the world. Features: - TCS 2.0 creates a more robust, easily installed and dependable tubeless system. - A recessed channel along the center of TCS 2.0 rims allows installation of the all-new Solid Strip, which prevents tubeless tape from sagging at the spoke holes and results in a smooth, consistent interface between the tire and rim. - 4D angled spoke drilling eliminates binding and lateral loading, and disperses tension more evenly over a greater area.

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

- Light enough to take XC racing but was born from research and testing on the Enduro World Series circuit, making it a great rim for anyone looking to improve both descending and climbing - Asymmetric rim design allows for a stronger wheel while offering the easy inflation and Stan's trademark unmatched airtight seal. - 28mm internal width ideal for 2.2-2.5" tires - Light and durable 6069 aluminum with welded joint and reinforced spoke bed

- Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires - E-sync hubs Specs: - Wheel Tire Type: Tubeless Ready - Wheel-Brake Comp.: Disc IS 6-bolt - Rim Material: Aluminum - Spoke Type: Sapim D-Light - Valve: Presta - Rim Construction: Double wall

The new Flow MK3 is wider, stronger, and lighter. The Flow’s legendary history on the World Cup DH circuit, combined with WideRight 29mm internal width offers the perfect balance of tire stability for outstanding control at any speed. Genuine Bead Socket Technology rolls faster, corners harder, and withstands even bigger hits. Combined with a new shape, the Flow MK3 is born and bred for control at speed and perfect for technical trails and enduro racing. Laterally stiffer and more durable, the new alloy is also even lighter, putting the new Flow MK3 in a class by itself for all-mountain performance. Flow MK3 wheels include: pre-installed tape for tubeless use and presta valve; 15x100mm front wheels include quick-release end caps and quick release. - 29mm internal width for tires up to 2.8-inches - Low-profile shape rolls faster, lasts longer, and helps stop tire pinch flats - Even lighter than the Flow EX - Laterally stiffer and stronger for improved handling - 25% stiffer and stronger for improved handling - More durable rim shape and alloy - Neo hubs accelerate quicker and last longer - Built on the proven success of the Flow EX on the World Cup DH circuit - Most trusted tubeless system for easy setup and low maintenance - Sapim Secure Lock aluminum nipples

Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place

Front SealLock end caps for Neo OS and Neo Ultimate OS hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Not compatible with non-OS hubs or Centerlock hubs.

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Sta Tru Rear Wheels - Hub/Brake Compatibility: Rim Brake - Wheel Size: 27" - Cassette Body Type: Threaded Standard 1.37" x 24tpi - ISO Diameter: 630 / 27" - Tire Type: Clincher

Shimano's 105 Front Hub is an excellent beginning to a strong, light front wheel. The diamond-polished bearing races mean the hub rolls super smoothly and the labyrinth seals shut out dust, dirt and water. Plus, the cold-forged-aluminum hub shell is beautiful and built to last. You get Shimano's excellent quick-release skewer, too.

With simple setup and reliable trail performance, the Shimano Deore XT 8100 front hub is perfect for custom MTB wheel builds. - Easy disc brake rotor installation with Center Lock spline mount and lock ring - Tool-less 15mm thru axle system optimizes rigidity and weight - Simple setup and reliable trail performance

For optimum wheel strength and reliability, Shimano's Dura-Ace Rear Freehub is made of cold-forged aluminum with an oversize shell, sturdy flanges, a titanium freewheel body and a 15mm internal axle. Inside, diamond-polished bearing races and stainless-steel ball bearings minimize rolling resistance, while high-tech seals keep out water and dirt for maximum durability. This hub also features tool-free bearing adjustment for easy maintenance, plus a light and strong aluminum/steel quick-release skewer.

With stunning acceleration, the new DURA-ACE R9270 C36 wheelset will change the way you experience climbs, corners, even stop lights. This is because it isn't just how much a wheel weighs but where the weight is on the wheel that matters. The all-new C36 design shaves mass at every opportunity but especially at the rim. The result is a lively wheelset that can transform your ride. With both a lighter, wider all-carbon rim and a lighter hub, the new DURA-ACE C36 won't shy away from a day of climbing. The new rim is 36 mm deep and still delivers good aerodynamic efficiency despite its gossamer weight. Meanwhile the hub features an alloy FREEHUB body and new engagement mechanism for increased rigidity. - 36 mm height full carbon rim - Internal rim width: 21 mm - DIRECT ENGAGEMENT - Compatible only with Shimano road 12-speed cassette sprockets

The Shimano HB-RS470 front disc brake hub features a Center Lock design, Internal Grease Sleeve, and Cup and Cone Bearing technology. - The Center Lock system makes for easy rotor installation with a quick and secure spline mount and lock ring - Hub features internal o-rings and a grease sleeve that helps maintain grease levels and increases service life

Shimano's SLX 15mm through-axle hub is ready for the trails. This rock-solid hub features smooth-rolling and easy to service cup-and-cone bearings. The stout design minimizes fork flex, improves steering precision and builds into a super-solid wheel, perfect for today's long-travel, yet lightweight forks. All-mountain durability ensures that whether you're hammering uphill or sticking sick landings this robust hub will hold up ride after ride. Plus Shimano's Center Lock spline makes mounting the disc-brake rotor super easy.

With a shallow-depth aero profile and lively acceleration, the ULTEGRA R8170 C36 wheelset is a climber's delight that delivers performance every road rider will appreciate. With the speed and efficiency of tubeless tires, the everyday performance of a shallow, aero profile carbon rim, and the convenience of 11 and 12-speed compatibility, the new ULTEGRA R8170 C36 wheelset is an upgrade for any road bike. - 36 mm height full carbon rim - Internal rim width: 21 mm - Shared rim profile with R9200 DURA-ACE wheels - Improved aerodynamics